StikNPeel™ Rework Stencils

StikNPeel™ Rework Stencils

Lead Time: Ships with 24-48 hours
Data Sheet

StikNPeel™ greatly simplifies the ability to selectively print solder paste onto various areas of a PCB. Simply peel off the backing, place the StikNPeel™ onto the PCB and apply the paste.

  • StikNPeel comes in a pack of 10 stencils
  • This rework process overcomes many of the headaches of using metal stencils
  • Eliminates "smearing" of solder paste underneath the stencil
  • Co planarity between board and stencil is assured due to the adhesive backing on the stencil

This unique stenciling System is very simple to use.

  • Stencil Thickness: 004in (.10mm), .005in (.13mm) and .006in (.15mm)
  • Minimum Aperture Size: .002in (.05mm)
  • Stencil Material: .Plastic film with release liner. Adhesive is a low tack sticky note type of adhesive.
  • MinimumPitch: .020in (0.5mm)
  • Maximum Area: Approx 4 x 4in (68mm x 68mm)

Tired of having to clean metal rework stencils between each print? Tired of cleaning up smeared solder paste because your PCB is warped or your stencil has shifted during the rework printing process? Frustrated by the time/effort it takes to tape off areas in and around the areas to be reworked?

The StikNPeel™ process greatly simplifies the ability of a rework or an assembly technician to selectively print solder paste onto various areas of a PCB. Simply peel off the backing, place the StikNPeel™ onto the PCB sliding it on/around until the apertures are aligned over the pads. Solder paste is then rolled in to the apertures of the stencil as many times as necessary-there is no smearing because it is held in place by the "sticky note" like adhesive. You can squeegee across the stencil face as many times as you want. The stencil is finally peeled off the PCB leaving very consistent solder paste in the aperture areas.

This rework process overcomes many of the headaches of using metal stencils. Firstly co planarity between board and stencil is assured due to the adhesive backing on the stencil. This eliminates "smearing" of solder paste underneath the stencil. First pass yields are improved as you get numerous rolls of the solder paste back and forth into the apertures once the stencil is aligned and is pressed in to place­it will not move. This insures consist solder paste volume. The problem of devices being right up against the device being reworked is overcome with this stencil design as the stencil can be "flipped up" very close to the edge of the package being reworked. We can design the stencil eliminating the need for a time consuming "masking" operation in and around the area to be reworked.

The rework stencils are packaged and delivered to you the way you want. Stencils are custom made to your exact device requirements without expensive tooling. They are also packaged such that developers and those building PCB prototypes can use them in quantities which closely match their needs.

FAQ's
User instructions

1. Peel backing off the stencil
2. Align and adhere stencil to PCB location
3. Roll solder paste in to apertures
4. Peel stencil off
5. Place device, reflow and inspect

Customer Reviews

This product has no reviews, please share your opinion of the product

Write a review
PRODUCT PRICING
Price:  $90.00

* Required information
Part Number: *

Data Sheet(s):

Special Instructions:

ACCESSORIES
() Squeegee Kit 1
Price: $35.00 Qty:
() Squeegee Kit 2
Price: $35.00 Qty:
() Squeegee Kit 3
Price: $35.00 Qty:
() Squeegee Kit 4
Price: $35.00 Qty:
() Squeegee Kit 5
Price: $35.00 Qty:
() Squeegee Kit 6
Price: $35.00 Qty:
() Squeegee Kit 7
Price: $35.00 Qty:
() Squeegee Kit 8
Price: $35.00 Qty: